The top adjusting 'TR' unit, used for light roughing and fine finishing operations, it is mounted directly into a tool hole in the bar or holder. 'TR' units are recommended for depths of cut up to .010”/ 0.25mm.

'R' units and top adjusting 'TR' units are available in 5 different sizes in both right and left hand, and have a minimum bore of 15.87mm.

Use 'R' units for roughing & semi-finishing.

Features:

  • Unique Design incorporating a precision ground collet
  • Split collet clamps to ACME type thread for accuracy and strength
  • Separate graduated dial seated on top face of hole
  • Rigidity maintained throughout full adjustment of unit

Benefits:

  • No deflection under load on eneven or intermittent cutting
  • Greater repeatability
  • Longer Insert Life
  • Most positive direct adjustment, high degree of rigidity, no dial slip when adjusting
  1. Insert the unit and roughly adjust as for type ‘R’.
  2. Using a hexagon wrench, tighten the retaining screw to fully compress the spring stack and back-off 12 turn max.
  3. Obtain final size by adjusting the dial only. Do not change the retaining screw setting.
    • When adjusting for a smaller diameter, always adjust under-size and then adjust clockwise to size.
    • ‘TR’ units are supplied with retaining screw and spring stack assembled in the correct order.
    • In the event that the spring stack becomes separated from the retaining screw and needs to be fitted, always remember that the disc spring nearest the unit should be with its outer rim towards the unit and other disc springs alternating as illustrated.
  4. This will ensure that the outer rim of the disc spring seats against the counterbore in the back of the boring bar (note: the number of disc springs varies with the unit size).

In extreme cutting conditions i.e. interrupted cuts etc. the action of the ‘TR’ unit can be made more rigid by re-stacking these disc springs, i.e. double stacking, but note that this will halve the adjustment range and must be pre-loaded by backing off the retaining screw only 14 turn (or less).

Additional disc springs may have to be purchased to achieve this. 'TR' units, as supplied are fitted with:

Unit Disc Springs
Size 2 6
Size 3 5
Size 5 3
Size 7 4
Size 10 4

For flexibility of use, the ‘TR’ unit can be used as for the standard ‘R’ unit, i.e. by fully tightening the retaining screw. In this way, the ‘TR’ unit becomes only marginally less rigid than the standard ‘R’ unit but will reduce the effective life of the disc springs that lose their spring characteristics after sustained full compression.

'TR' Units - Angular Mounted - Size 2 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 23.60 0.930 0.2 0.008 4.5 0.177 9.4 0.370 1.35 0.053 TC_ _ 06T1 (02) TR2A2
TR2A2-LH
20.90 0.823 2.0 0.079 TR2B2
TR2B2-LH
18.57 0.731 0.75 0.029 TR2B2S
TR2B2S-LH
23.60 0.929 2.0 0.079 12.6 0.496 TR2B3
75° 25.70 1.011 4.5 0.177 10.0 0.394 -1.50 -0.059 TR2A2L
TR2A2L-LH
23.10 0.909 2.0 0.079 TR2B2L
TR2B2L-LH
45° 25.30 0.995 4.5 0.177 -1.60 -0.063 TR2A245
22.80 0.897 2.0 0.079 TR2B245
'TR' Units - Angular Mounted - Size 3 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 30.8 1.212 0.28 0.011 7.3 0.290 13.45 0.529 0.8 0.031 TC_ _ 0902 (04) TR3A2
TR3A2-LH
27.6 1.087 4.0 0.157 TR3B2
TR3B2-LH
25.6 1.008 TR3B1
11.25 0.443 1.32 0.051 TC_ _ 06T1 (02) TR3B1-LH
29.2 1.149 7.3 0.290 11.10 0.437 0.2 0.008 CC_ _ 0602 (04) TR3A2C
TR3A2C-LH
26.1 1.027 4.0 0.157 TR3B2C
TR3B2C-LH
26.25 1.033 1.5 0.059 TR3B2CS
75° 30.7 1.209 7.3 0.290 13.55 0.533 1.1 0.036 TC_ _ 0902 (04) TR3A2L
TR3A2L-LH
27.5 1.083 4.0 0.157 TR3B2L
TR3B2L-LH
26.25 1.033 1.5 0.059 10.47 0.412 -0.33 -0.840 CC_ _ 0602 (04) TR3B2LSC
45° 32.9 1.295 7.3 0.287 14.50 0.571 -1.6 -0.063 TC_ _ 0902 (04) TR3A245
TR3A245-LH
29.6 1.165 4.0 0.157 TR3B245
30° 32.2 1.268 7.3 0.287 TR3A230
'TR' Units - Angular Mounted - Size 5 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 41.5 1.634 0.4 0.016 10.7 0.421 16.95 0.667 2.3 0.090 TC_ _ 1102 (04) TR5A2
TR5A2-LH
36.5 1.437 5.6 0.220 TR5B2
TR5B2-LH
41.0 1.614 10.7 0.421 15.90 0.626 1.2 0.047 CC_ _ 0602 (04) TR5A2C
TR5A2C-LH
35.9 1.413 5.6 0.220 TR5B2C
TR5B2C-LH
95° 41.5 1.634 10.7 0.421 16.95 0.667 2.3 0.090 TC_ _ 1102 (04) TR5A295
36.5 1.437 5.6 0.220 TR5B295
41.0 1.614 10.7 0.421 15.60 0.614 1.2 0.047 CC_ _ 0602 (04) TR5A295C
75° 41.5 1.634 10.7 0.421 16.55 0.625 1.3 0.051 TC_ _ 1102 (04) TR5A2L
36.5 1.437 5.6 0.220 TR5B2L
TR5B2L-LH
45° 43.5 1.712 10.7 0.421 17.00 0.669 -1.6 -0.063 TR5A245
TR5A245-LH
38.5 1.516 5.6 0.220 TR5B245
TR5B245-LH
30° 42.0 1.654 10.7 0.421 16.30 0.641 -1.6 -0.063 TR5A230
36.8 1.449 5.6 0.220 TR5B230
'TR' Units - Angular Mounted - Size 7 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 61.5 2.421 0.6 0.024 12.8 0.504 25.55 1.006 -0.40 -0.016 TC_ _16T3 (08) TR7A2
TR7A2-LH
57.0 2.244 8.0 0.315 TR7B2
TR7B2-LH
61.0 2.401 12.8 0.504 26.57 1.046 -1.58 -0.062 CC__ 09T3(04) TR7A2C
TR7A2C-LH
55.9 2.201 8.0 0.315 TR7B2C
TR7B2C-LH
95° 59.5 2.343 12.8 0.504 25.55 1.006 -0.26 -0.010 TC_ _ 16T3 (08) TR7A295
61.0 2.401 26.57 1.046 -1.60 -0.063 CC_ _ 09T3 (04) TR7A295C
75° 61.5 2.421 12.8 0.504 23.40 0.921 -3.20 -0.126 TC_ _ 16T3 (08) TR7A2L
TR7A2L-LH
57.0 2.244 8.0 0.315 TR7B2L
TR7B2L-LH
45° 63.9 2.516 12.8 0.504 25.50 1.004 -6.50 -0.256 TR7A245
58.8 2.315 8.0 0.315 TR7B245
'TR' Units - Angular Mounted - Size 10 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 81.5 3.209 0.7 0.027 23.0 0.906 31.70 1.248 -0.40 -0.016 TC_ _ 16T3 (08) TR10A2
TR10A2-LH
71.5 2.815 12.8 0.504 TR10B2
TR10B2-LH
81.5 3.209 23.0 0.906 31.24 1.230 0.79 0.031 CC_ _ 1204 (04) TR10A2C
95° 81.5 3.209 23.0 0.906 31.70 1.248 -0.26 -0.010 TC_ _ 16T3 (08) TR10A295
71.5 2.815 12.8 0.504 TR10B295
75° 81.5 3.209 23.0 0.906 31.10 1.224 -0.90 -0.035 TR10A2L
TR10A2L-LH
71.5 2.815 12.8 0.504 TR10B2L
TR10B2L-LH
45° 84.0 3.307 23.0 0.906 31.80 1.252 -3.20 -0.126 TR10A245
'TR' Units - Square Mounted - Size 2 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 27.60 1.087 0.25 0.010 5.5 0.216 9.40 0.370 2.0 0.078 TC_ _ 06T1 (02) TR2A5
TR2A5-LH
24.40 0.961 2.5 0.098 TR2B5
TR2B5-LH
27.60 1.087 5.5 0.216 7.5 0.295 TR2F5
24.40 0.961 2.5 0.098 TR2F5S
75° 27.60 1.087 5.5 0.216 9.40 0.370 2.0 0.078 TR2A5L
TR2A5L-LH
24.40 0.961 2.5 0.098 TR2B5L
TR2B5L-LH
45° 28.40 1.118 5.5 0.216 10.00 0.393 -0.8 -0.031 TR2A245
25.20 0.992 2.5 0.098 TR2B245
28.00 1.102 5.5 0.216 9.50 0.374 TR2A90
25.00 0.984 2.5 0.098 TR2B90
'TR' Units - Square Mounted - Size 3 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 35.1 1.382 0.35 0.014 9.1 0.359 12.3 0.484 3.0 0.118 TC_ _ 0902 (04) TR3A5
TR3A5-LH
31.1 1.224 5.0 0.197 TR3B5
TR3B5-LH
34.0 1.338 9.1 0.359 11.1 0.437 4.0 0.158 CC_ _ 0602 (04) TR3A5C
TR3A5C-LH
30.0 1.181 5.0 0.197 TR3B5C
TR3B5C-LH
36.5 1.437 9.1 0.359 12.9 0.508 9.4 0.370 TC_ _ 0902 (04) TR3F5
32.5 1.279 5.0 0.197 TR3F5S
TR3F5S-LH
75° 35.1 1.381 9.1 0.359 12.3 0.484 2.0 0.079 TR3A5L
TR3A5L-LH
31.1 1.224 5.0 0.197 TR3B5L
TR3B5L-LH
45° 37.2 1.465 9.1 0.358 14.5 0.571 -0.8 -0.310 TR3A545
33.2 1.307 5.0 0.197 TR3B545
36.5 1.437 9.1 0.358 14.0 0.551 TR3A90
32.5 1.279 5.0 0.197 TR3B90
'TR' Units - Square Mounted - Size 5 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 48.0 1.890 0.50 0.020 13.4 0.528 16.1 0.634 5.4 0.213 TC_ _ 1102 (04) TR5A5
TR5A5-LH
41.5 1.634 7.0 0.276 TR5B5
TR5B5-LH
49.4 1.965 13.4 0.528 15.9 0.628 CC_ _ 0602 (04) TR5A5C
TR5A5C-LH
43.0 1.693 7.0 0.276 TR5B5C
48.0 1.890 13.4 0.528 16.1 0.634 15.0 0.591 TC_ _ 1102 (04) TR5F5
TR5F5-LH
41.5 1.634 7.0 0.276 TR5F5S
49.4 1.965 13.4 0.528 15.9 0.626 CC_ _ 0602 (04) TR5F5C
TR5F5C-LH
95° 48.0 1.890 13.4 0.528 16.1 0.634 TC_ _ 1102 (04) TR5F595
75° 48.0 1.890 13.4 0.528 3.2 0.126 TR5A5L
TR5A5L-LH
41.5 1.634 7.0 0.275 TR5B5L
TR5B5L-LH
45° 48.8 1.921 13.4 0.528 -1.6 -0.063 TR5A545
TR5A545-LH
42.4 1.661 7.0 0.275 TR5B545
48.7 1.917 13.4 0.528 TR5A90
42.3 1.665 7.0 0.275 TR5B90
'TR' Units - Square Mounted - Size 7 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 70.5 2.775 0.75 0.030 16.0 0.630 25.5 1.004 8.35 0.329 TC_ _ 16T3 (08) TR7A5
TR7A5-LH
64.0 2.250 10.0 0.394 TR7B5
TR7B5-LH
70.5 2.775 16.0 0.630 25.4 1.000 6.35 0.250 CC_ _ 09T3 (04) TR7A5C
10.0 0.394 TR7B5C
16.0 0.630 25.5 1.004 20.00 0.787 TC_ _ 16T3 (08) TR7F5
TR7F5-LH
25.4 1.000 CC_ _ 09T3 (04) TR7F5C
TR7F5C-LH
95° 70.5 2.775 16.0 0.630 25.5 1.004 8.47 0.333 TC_ _ 16T3 (08) TR7A595
6.20 0.244 TR7A5L
TR7A5L-LH
75° 64.0 2.520 10.0 0.394 TR7B5L
TR7B5L-LH
70.5 2.775 16.0 0.630 15.80 0.622 TR7F5L
45° 69.2 2.724 16.0 0.630 -1.60 -0.063 TR7A545
62.8 2.472 100 0.393 TR7B545
30° 70.5 2.775 16.0 0.630 TR7A530
66.0 2.600 16.0 0.630 23.0 0.920 TR7A590
59.5 2.342 100 0.394 TR7A590
'TR' Units - Square Mounted - Size 10 Units
Approach Angle Min Bore
Possible
T
Top Adj
R
Total Radial Adjustment
H
Min Height
K
Tool Point Offset
Insert & Datum Rad Part Number
mm inch mm inch mm inch mm inch mm inch
90° 96.0 3.780 0.87 0.034 28.7 1.130 31.80 1.252 9.5 0.374 TC_ _ 16T3 (08) TR10A5
TR10A5-LH
83.5 3.287 16.0 0.630 TR10B5
TR10B5-LH
96.0 3.780 28.7 1.130 31.75 1.250 CC_ _ 1204 (04) TR10A5C
83.5 2.87 16.0 0.630 TR10B5C-LH
96.0 3.780 28.7 1.130 31.80 1.252 25.4 1.000 TC_ _ 16T3 (08) TR10F5
TR10F5-LH
31.75 1.250 CC_ _ 1204 (04) TR10F5C
95° 96.0 3.780 9.54 0.376 CC_ _ 1204 (04) TR10A595C
25.52 1.005 TC_ _ 16T3 (08) TR10F595
25.44 1.002 CC_ _ 1204 (04) TR10F595C
TR10F595C-LH
75° 96.0 3.780 31.80 1.252 4.8 0.189 TC_ _ 16T3 (08) TR10A5L
TR10A5L-LH
83.5 3.287 16.0 0.630 TR10B5L
TR10B5L-LH
96.0 3.780 28.7 1.130 20.35 0.801 TR10F5L
45° 95.0 3.740 31.80 1.252 -1.6 -0.063 TR10A545
TR10A545-LH
84.0 3.307 16.0 0.630 TR10B545
80.5 3.170 28.7 1.130 28.60 1.126 TR10A90
16.0 0.630 TR10B90
Mounting Dimensions - Standard Rigibore Units - Metric
UNIT
PREFIX
A
+.013
-0
B
+.13
-0
C
+.25
-0
D
+/-.25
E
+/-.05
F
+/-0.1
G
+0
-.02
J
+0.1
-0
M
(Sth)
N
+.25
-0
P
+.05
-0
Q
+.02
-0
R2BS 6.35 12.80 8.00 19.00 13.70 7.80 3.00 1.85 4.00 6.35 3.80 1.60
R2B_/TR2B_ 9.50
R2A_/TR2A_ 12.70
R2F_/TR2F_
R3B_/TR3B_ 7.937 16.00 11.30 26.00 18.00 11.00 4.00 4.00 5.50 11.90 5.05 2.34
R3A_/TR3A_ 15.90
R3F_/TR3F_
R5B_/TR5B_ 12.70 25.66 16.00 38.00 27.00 15.60 5.60 7.00 5.50 19.00 7.55 3.155
R5A_/TR5A_ 25.40
R5F_/TR5F_
R7B_/TR7B_ 19.05 35.20 24.00 48.00 37.50 23.70 8.70 13.00 11.00 25.40 11.35 4.76
R7A_/TR7A_ 31.75
R7F_/TR7F_
R10B_/TR10B_ 25.40 44.70 32.00 57.00 48.00 31.50 9.40 16.50 14.50 35.00 14.95 6.32
R10A_TR10A_ 47.60
R10F_/TR10F_
Mounting Dimensions - Standard Rigibore Units - Imperial
UNIT PREFIX A +.0005 -0 ⌀ B +.005 -0 ⌀ C +.010 -0 ⌀ D +.01 E +/-.002 ⌀ F +/-.004 ⌀ G +0 -.008 J +.004 -0 M (Sth) N +.010 -0 B/A P +.002 -0 Q +.001 -0
R2B_S .2500 .5040 .3150 .7500 .5400 .3070 .1180 .1180 .1570 .2500 .1500 .0630
R2B_/TR2B_ .3750
R2A_/TR2A_ .5000
R2F_/TR2F_
R3B_/TR3B_ .3125 .6300 .4450 1.030 .7090 .4330 .1580 .1580 .2170 .4690 .1990 .0920
R3A_/TR3A_ .6250
R3F_/TR3F_
R5B_/TR5B_ .5000 1.010 .6300 1.500 1.063 .6100 .2200 .2760 .2170 .7500 .2970 .1240
R5A_/TR5A_ 1.000
R5F_/TR5F_
R7B_/TR7B_ .7500 1.386 .9450 1.870 1.476 .9330 .3430 .5120 .4330 1.000 .4470 .1870
R7A_/TR7A_ 1.250
R7F_/TR7F_
R10B_/TR10B_ 1.000 1.760 1.260 2.250 1.890 1.240 .3700 .6500 .5710 1.375 .5890 .2490
R10A_/TR10A_ 1.875
R10F_/TR10F_
Spares & Accessories - Size 2 Units - Angular Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R2A2 R20A2 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A2 R20A2 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2A2-LH R20A2-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A2-LH R20A2-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2B2 R20B2 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B2 R20B2 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2B2-LH R20B2-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B2-LH R20B2-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2B2S R20B2S R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BS
TR2B2S R20B2S R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BS R29
R2B2S-LH R20B2S-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BS
TR2B2S-LH R20B2S-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BS R29
R2B3 R20B3 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B3 R20B3 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2A2L R20A2L R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A2L R20A2L R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2A2L-LH R20A2L-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A2L-LH R20A2L-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2B2L R20B2L R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B2L R20B2L R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2B2L-LH R20B2L-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B2L-LH R20B2L-LH R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2A245 R20A245 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A245 R20A245 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2B245 R20B245 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B245 R20B245 R212 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
Spares & Accessories - Size 3 Units - Angular Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R3A2 R30A2 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A2 R30A2 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3A2-LH R30A2-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A2-LH R30A2-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3B2 R30B2 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B2 R30B2 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3B2-LH R30B2-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B2-LH R30B2-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3B1 R30B1 R312 R32 R35 R34 R36 R38 R37 R37D RS2045 R33B
TR3B1 R30B1 R312 R32 R35 R34 R36 R38 R37 R37D RS2045 R33BT R39
R3B1-LH R30B1-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2045 R33B
TR3B1-LH R30B1-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2045 R33BT R39
R3A2C R30A2C R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33A
TR3A2C R30A2C R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33AT R39
R3A2C-LH R30A2C-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33A
TR3A2C-LH R30A2C-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33AT R39
R3B2C R30B2C R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33B
TR3B2C R30B2C R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33BT R39
R3B2C-LH R30B2C-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33B
TR3B2C-LH R30B2C-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33BT R39
R3B2CS R30B2CS R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33B
TR3B2CS R30B2CS R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33BT R39
R3B295 R30B295 R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33B
TR3B295 R30B295 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3A2L R30A2L R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A2L R30A2L R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3A2L-LH R30A2L-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A2L-LH R30A2L-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3B2L R30B2L R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B2L R30B2L R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3B2L-LH R30B2L-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B2L-LH R30B3L-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3B2LSC R30B2LSC R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33B
TR3B2LSC R30B2LSC R312 R32 R35 R34 R36 R38 R37 R37D RS2560 R33BT R39
R3A245 R30A245 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A245 R30A245 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3A245-LH R30A245-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A245-LH R30A245-LH R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3B245 R30B245 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B245 R30B245 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3A230 R30A230 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A230 R30A230 R312 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
Spares & Accessories - Size 5 Units - Angular Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R5A2 R50A2 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A2 R50A2 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A2-LH R50A2-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A2-LH R50A2-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B2 R50B2 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B2 R50B2 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5B2-LH R50B2-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B2-LH R50B2-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5A2C R50A2C R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A2C R50A2C R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A2C-LH R50A2C-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A2C-LH R50A2C-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B2C R50B2C R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B2C R50B2C R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5B2C-LH R50B2C-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B2C-LH R50B2C-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5A295 R50A295 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A295 R50A295 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B295 R50B295 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B295 R50B295 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5A295C R50A295C R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A295C R50A295C R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A2L R50A2L R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A2L R50A2L R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B2L R50B2L R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B2L R50B2L R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5B2L-LH R50B2L-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B2L-LH R50B2L-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5A245 R50A245 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A245 R50A245 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A245-LH R50A245-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A245-LH R50A245-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B245 R50B245 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B245 R50B245 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5B245-LH R50B245-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B245-LH R50B245-LH R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5A230 R50A230 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55A
TR5A230 R50A230 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B230 R50B230 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R55B
TR5B230 R50B230 R512 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
Spares & Accessories - Size 7 Units - Angular Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R7A2 R70A2 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A2 R70A2 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A2-LH R70A2-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A2-LH R70A2-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B2 R70B2 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B2 R70B2 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7B2-LH R70B2-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B2-LH R70B2-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7A2C R70A2C R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A2C R70A2C R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A2C-LH R70A2C-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A2C-LH R70A2C-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B2C R70B2C R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B2C R70B2C R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7B2C-LH R70B2C-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B2C-LH R70B2C-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7A295 R70A295 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A295 R70A295 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A295C R70A295C R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A295C R70A295C R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A2L R70A2L R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A2L R70A2L R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A2L-LH R70A2L-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A2L-LH R70A2L-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B2L R70B2L R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B2L R70B2L R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7B2L-LH R70B2L-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B2L-LH R70B2L-LH R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7A245 R70A245 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A245 R70A245 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B245 R70B245 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B245 R70B245 R712 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
Spares & Accessories - Size 10 Units - Angular Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
Shim Screw Wrench
(Size 10)
R10A2 R100A2 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A2 R100A2 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A2-LH R100A2-LH R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A R118
TR10A2-LH R100A2-LH R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109 R118
R10B2 R100B2 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B
TR10B2 R100B2 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10B2-LH R100B2-LH R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B R118
TR10B2-LH R100B2-LH R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109 R118
R10A2C R100A2C R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A2C R100A2C R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A295 R100A295 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A R118
TR10A295 R100A295 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109 R118
R10B295 R100B295 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B
TR10B295 R100B295 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10A2L R100A2L R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A R118
TR10A2L R100A2L R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109 R118
R10B2L R100B2L R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B
TR10B2L R100B2L R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10B2L-LH R100B2L-LH R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B R118
TR10B2L-LH R100B2L-LH R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109 R118
R10A295 R100A295 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A295 R100A295 R112 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
Spares & Accessories - Size 2 Units - Square Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R2A5 R20A5 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A5 R20A5 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2A5-LH R20A5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A5-LH R20A5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2B5 R20B5 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B5 R20B5 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2B5-LH R20B5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B5-LH R20B5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2F5 R20F5 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2F5 R20F5 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2F5S R20F5S R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2F5S R20F5S R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2A5L R20A5L R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A5L R20A5L R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2A5-LH R20A5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A5-LH R20A5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2B5L R20B5L R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B5L R20B5L R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2B5-LH R20B5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B5-LH R20B5-LH R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2A545 R20A545 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A545 R20A545 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2B545 R20B545 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B545 R20B545 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
R2A90 R20A90 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23A
TR2A90 R20A90 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23AT R29
R2B90 R20B90 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23B
TR2B90 R20B90 R215 R22 R25 R24 R26 R28 R27 R27D RS2045 R23BT R29
Spares & Accessories - Size 3 Units - Square Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R3A5 R30A5 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A5 R30A5 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3A5-LH R30A5-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A5-LH R30A5-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3B5 R30B5 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B5 R30B5 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3B5-LH R30B5-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B5-LH R30B5-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3A5C R30A5C R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33A
TR3A5C R30A5C R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33AT R39
R3A5C-LH R30A5C-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33A
TR3A5C-LH R30A5C-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33AT R39
R3B5C R30B5C R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33B
TR3B5C R30B5C R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33BT R39
R3B5C-LH R30B5C-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33B
TR3B5C-LH R30B5C-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2560 R33BT R39
R3F5 R30F5 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3F5 R30F5 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3F5S R30F5S R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3F5S R30F5S R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3F5S-LH R30F5S-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3F5S-LH R30F5S-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3A5L R30A5L R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A5L R30A5L R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3A5L-LH R30A5L-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A5L-LH R30A5L-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3B5L R30B5L R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B5L R30B5L R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3B5L-LH R30B5L-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B5L-LH R30B5L-LH R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3A545 R30A545 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A545 R30A545 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3B545 R30B545 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B545 R30B545 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
R3A90 R30A90 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33A
TR3A90 R30A90 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33AT R39
R3B90 R30B90 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33B
TR3B90 R30B90 R315 R32 R35 R34 R36 R38 R37 R37D RS2263 R33BT R39
Spares & Accessories - Size 5 Units - Square Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R5A5 R50A5 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A5 R50A5 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A5-LH R50A5-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A5-LH R50A5-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B5 R50B5 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5B5 R50B5 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5B5-LH R50B5-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5B5-LH R50B5-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5A5C R50A5C R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A5C R50A5C R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A5C-LH R50A5C-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A5C-LH R50A5C-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B5C R50B5C R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5B5C R50B5C R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5F5 R50F5 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5F5 R50F5 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5F5-LH R50F5-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5F5-LH R50F5-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5F5S R50F5S R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5F5S R50F5S R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5F5C R50F5C R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5F5C R50F5C R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5F5C-LH R50F5C-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5F5C-LH R50F5C-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5F595 R50F595 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5F595 R50F595 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A5L R50A5L R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A5L R50A5L R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A5L-LH R50A5L-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A5L-LH R50A5L-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B5L R50B5L R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5B5L R50B5L R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5B5L-LH R50B5L-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5B5L-LH R50B5L-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A545 R50A545 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A545 R50A545 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5A545-LH R50A545-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A545-LH R50A545-LH R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B545 R50B545 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5B545 R50B545 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
R5A90 R50A90 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53A
TR5A90 R50A90 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53AT R59
R5B90 R50B90 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53B
TR5B90 R50B90 R515 R52 R55 R54 R36 R58 R37 R37D RS2560 R53BT R59
Spares & Accessories - Size 7 Units - Square Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
R7A5 R70A5 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A5 R70A5 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A5-LH R70A5-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A5-LH R70A5-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B5 R70B5 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B5 R70B5 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7B5-LH R70B5-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B5-LH R70B5-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7A5C R70A5C R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A5C R70A5C R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B5C R70B5C R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B5C R70B5C R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7F5 R70F5 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7F5 R70F5 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7F5-LH R70F5-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7F5-LH R70F5-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A595 R70A595 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A595 R70A595 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7F595 R70F595 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7F595 R70F595 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7F595C R70F595C R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7F595C R70F595C R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A5L R70A5L R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A5L R70A5L R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A5L-LH R70A5L-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A5L-LH R70A5L-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B5L R70B5L R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B5L R70B5L R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7B5L-LH R70B5L-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B5L-LH R70B5L-LH R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7F5L R70F5L R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7F5L R70F5L R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A545 R70A545 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A545 R70A545 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B545 R70B545 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73B
TR7B545 R70B545 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT R79
R7A530 R70A530 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A530 R70A530 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7A90 R70A90 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73A
TR7A90 R70A90 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73AT R79
R7B90 R70B90 R715 R72 R75 R74 R76 R78 R77 R77D RS4084
TR7B90 R70B90 R715 R72 R75 R74 R76 R78 R77 R77D RS4084 R73BT
Spares & Accessories - Size 10 Units - Square Mounted
Tool Tool Body Dial Collet Collet Spring Key Adjusting Wrench Hexagon Wrench Torx Wrench Torx Driver Insert Screw Screw & Washer
(TR Unit)
Bolt
(R Unit)
Adjusting Spring Stack
(TR Unit)
Shim Screw Wrench
(Size 10)
R10A5 R100A5 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A R118
TR10A5 R100A5 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A5-LH R100A5-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A5-LH R100A5-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10B5 R100B5 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B
TR10B5 R100B5 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10B5-LH R100B5-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B R118
TR10B5-LH R100B5-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10A5C R100A5C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A5C R100A5C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A5C-LH R100A5C-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A5C-LH R100A5C-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10F5 R100F5 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10F5 R100F5 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109 R118
R10F5-LH R100F5-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10F5-LH R100F5-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10F5C R100F5C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10F5C R100F5C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A595C R100A595C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A595C R100A595C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A595C-LH R100A595C-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A R118
TR10A595C-LH R100A595C-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10F595 R100F595 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10F595 R100F595 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10F595C R100F595C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10F595C R100F595C R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10F595C-LH R100F595C-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10F595C-LH R100F595C-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109 R118
R10A5L R100A5L R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A5L R100A5L R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A5L-LH R100A5L-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A5L-LH R100A5L-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10B5L R100B5L R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B
TR10B5L R100B5L R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10B5L-LH R100B5L-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B R118
TR10B5L-LH R100B5L-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10F5L R100F5L R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10F5L R100F5L R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A545 R100A545 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A545 R100A545 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10A545-LH R100A545-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A R118
TR10A545-LH R100A545-LH R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10B545 R100B545 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B
TR10B545 R100B545 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109
R10A90 R100A90 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103A
TR10A90 R100A90 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103AT R109
R10B90 R100B90 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103B R118
TR10B90 R100B90 R115 R102 R105 R104 R76 R108 R77 R77D RS35120 R103BT R109

Rigibore Ltd | The Most Accurately Adjustable Boring Tools In The World

Company Number 01465509. Registered in England and Wales. VAT registration number GB 168268668

2017 Rigibore Ltd - Other companies in the Bassett group